Hoyles GEMINI Battery powered fire alarm Bedienungsanleitung PDF herunterladen

EOL

EA EB PA PB

EOL

EA EB PA PB

EOL

EA EB PA PB

EOL

EA EB PA PB

To Integral Callpoint

GX32CIE

GX32MCP

GX32MCP GX32MCP

PP3 PP3

PP3

Installation Testing the system

It is assumed that installers are familiar with installing cables and fixing the Turn the keyswitch to TEST MODE. The sounder will give a low pitch bleep

various components etc.. The system is battery powered and presents no every 5 secs. Insert the black test key in the underside of the call point to

electrical risk to either installers or users. Callpoint/Sounder units are displace the glass. Only the control sounder will sound. Remove the test key.

generally fitted at a height of 1.2m AFL. Remove the front cover and glass While still in TEST MODE visit each call point in turn. Inserting the black test

and separate the back box. Pre-drill the back boxes if necessary to take the key sounds only the sounder of the call point being tested. When all call

interconnection cable. Fit the back boxes to the wall and introduce the points have been tested switch the control to the RESTART position.

cable. Strip the sheathing and cores as necessary.

Fault Finding

Start connecting at the remote End of Line unit and work back towards the

Fault indication is given audibly and visually at the control and

control panel. Connect the Amber and Blue of the cable to PA and PB

respectively. Fit a link in the terminals marked EOL. Connect the battery.

The unit should bleep. This will be repeated every 10 secs.. Re-assemble

the unit onto the back box. Refit the glass - the sounder will give a double

whoop within 10 secs. to confirm correct installation. Refit and secure the

front cover. If on fitting the glass and cover a long tone followed by double

bleeps every 5 secs. this indicates that there is a problem on the previous

section. This could be: a short or open circuit on the cable, a reverse

connection, no battery in the previous unit or no EOL link fitted.

At the next unit connect the Amber and Blue of the cable from the End of

Line unit to EA and EB respectively of this unit. Connect the Amber and

Blue of the cable leading towards the control panel to PA and PB

respectively. Reassemble the unit as above and check for the double

whoop on this unit.

Repeat the above procedure at each unit. Do NOT start to connect the next

call point until you have heard the double whoop confirmation. At the

control panel connect Amber and Blue to EA and EB respectively. Ensure

that the keyswitch is in the RESTART position. Connect the batteries

(observe the correct polarity). The green system healthy LED should start

to flash within 10 - 15 secs.. Fit the control panel front onto its back box. If

the green LED does not flash check the batteries and cable connections in

the control and the first call point.

can be caused

by exhausted or partially exhausted batteries, cable connections or cable

damage. If fault indication occurs on installation or on extending the system it

could be that the end of line link is not fitted or two have been fitted.

Switch to TEST MODE, any call point with a partially exhausted battery will

give a single high pitched bleep at 5 sec. intervals. Remove the callpoint and

replace the battery while in TEST MODE. All Callpoint and Control panel

batteries should be changed.

A double high pitched bleep every 5 secs. indicates that there is a cable fault

between the bleeping unit and the next unit towards the end of line. This

could also indicate a totally exhausted battery in the next unit.

Any battery replacements or cabling alterations should be done with the

keyswitch in TEST MODE otherwise it will be necessary to follow the

installation procedure above.

If only part of the system is sounding as a fire condition and it is not possible to

silence it from the control this would indicate that a cable has been damaged

and it is not possible for the silence signal to be received. In this case it will be

necessary to remove the batteries from the sounding call points and follow

the installation procedure above.

NOTE: The GX32CIE is not able to silence smoke alarms that are still

sensing smoke. If it is not possible to silence the call points beyond this

detector this would indicate that some of the batteries are approaching the

battery fail point. It will be necessary to clear the smoke first.

GX32 Battery Powered Fire Alarm System

Pre-wired do not alter

Pre-wired

do not alter

Battery connections

Keyswitch

connections

E.O.L link must be fitted

to last call point on system

W:\Tech\Gemini GX32\Common\Installation Instructions\60074.cdr Page 1 Sep 2009 Iss 2

Amber

Blue

Black

Red

3 B

ery

- +

GX32SMi

GX32S/1

GX32 is available in kit form but

individual components can be

purchased as required.

GX32KIT400

1 x Gx32CIE Control Panel

4 x Gx32MCP Callpoint/sounders

GX32CAB140 140m twin cable

4 x CABCLIP5RBK 100 cable clips

GX32KIT402

1 x Gx32CIE Control Panel

4 x Gx32MCP Callpoint/sounders

2 x GX32SMi Ionisation smoke alarms

GX32CAB140 140m twin cable

4 x CABCLIP5RBK 100 cable clips

All kits and individual items are supplied

with batteries and fixing screws etc..

NOTE

Smoke alarms, where fitted, can

only be used between callpoint/

/sounder units. Only one can be

fitted between each as shown. Thus

32 smoke alarms would require 32

callpoint/sounder units.

Smoke alarms cannot be used at

the end of line.

Smoke alarms are provided with a

GX32S/1 termination unit to provide

the necessary termination

resistance for the GX32 system

www.hoyles.com

T. 01744 886600 E. [email protected]

F. 01744 886607 W. www.hoyles.com

Hoyles Electronic Developments Ltd

1 2

Inhaltsverzeichnis

Seite 1 - GX32MCP GX32MCP

EOLEA EB PA PBEOLEA EB PA PBEOLEA EB PA PBEOLEA EB PA PBEBEATo Integral CallpointGX32CIEGX32MCPGX32MCPGX32MCP GX32MCPPP3 PP3PP3PP3Installation Testing

Seite 2 - GX32 Fire Alarm System

Monitoring:1. Overview!Battery low monitoring gives audible and visual warning at the GX32CIE. Turning GX32CIE keyswitch to TEST MODE enable location